中文版|English

WELCOME TO FOSHAN YUANLI PRECISION MACHINERY CO.,LTD
TEL:13827748026

FOSHAN YUANLI PRECISION MACHINERY CO.,LTD

YUANLI PRECISION MACHINERY CO.,LTD—— DEVOTION MAKES PROFESSION ——                        

China's leading brand water jet cutting equipment

CONTACT US

FOSHAN YUANLI PRECISION MACHINERY CO.,LTD
FREE TEL:13827748026
TEL:0757-63856189
FAX:0757-63858669
E-MAIL:fsyuanli@hotmail.com
URL:http://en.fsyuanli.net/
ADD: No.3 Xingfa Road,Luocun Xiabai The Third Industrial Zone,Nanhai District Foshan Guangdong China

Industry Information POSITION:  HOME   >   NEWS>Industry Information  

Equipment usage skill

Data Source:Foshan Yuanli Precision machinery Co. , LTD Time:2015-11-26

1 after a period of time, it will be used for a period of time to continue to use it to improve the life of the nozzle.
- 2. Please users do not yield to the temptation of cheap to buy non manufacturers to provide spare parts, not only the spare parts quality cannot be guaranteed, also may be harmful to your device, cause greater losses. Also will lose manufacturers to your equipment warranty, is really not worth the candle.
3 users can back up the parameters in the numerical control system so that they can be recovered when needed.
- 4. The fault appears when users are unable to determine the cause of the malfunction, please detailed observation of fault phenomena (including oil pressure gauge and pressure gauge numerical, change the frequency, triggering breakdown of keys) reported to maintenance personnel, under the guidance of maintenance personnel analysis and determine the fault reason and to exclude.
5 you know how to quickly determine which end of the high and low pressure check valve seal is not good, in fact, we can use both hands to touch the high and low pressure parts of the two ends, the temperature on the high side of the sealing effect is certainly not good.
6 in order to prevent the leakage of steel pipe connection, must be the head of the steel pipe thread out of the screw thread three above.
- 7. When fault appears unable to determine the problem is in the water or oil, the waterway part removed (high pressure cylinder after the removal of), and then open the oil pump and high pressure water switch, observe the oil cylinder piston commutation is normal. To determine the problem is the water or oil circuit failure.
After 8 normal boot, has been pressed to open the high pressure water button is not loose, then the device will stop reversing and shows the maximum pressure. If the oil pressure gauge can be raised to the actual use of the pressure, you can determine the overflow valve is normal.
- 9. Normal boot but non reversing device, we can remove the valve on the two electric plugs. Then use hand alternate top reversing valves at both ends of the rubber cover inside spool. If the device can change, can determine the directional control valve is normal.
10 booster in the maintenance of the first boot, for the protection of equipment needs to be pressure down, and then slowly rose to the use of pressure.
11 Where the turbocharger is fitted with a sealing ring, it is required to add grease and grease when installing.
- 12 supercharger connect all threads are required to be painted blue oil, prevent thread seizure.
13 when installing the jewel nozzle and the sand nozzle, avoid by all means to tighten the screw thread. In order to prevent damage or crushed stones pinch off sand nozzle.
- 14. High pressure cylinder and a low pressure cylinder head connection at every two or three weeks of loose a thread, prevent high pressure cylinder and a low pressure cylinder head connection too tight.
15 every day before the normal boot, please check the relevant water, electricity, gas is all in place.
16 please make sure that the ambient temperature of the device is above zero to prevent parts from freezing equipment.
17 the cutting head is the best cutting height of the workpiece is 3mm-5mm.
18 when the numerical control system prompts limit or emergency stop alarm, the equipment is unable to open the high pressure water.
19 when the pressure relay on the pressure relay alarm or damage, the device is unable to open the oil pump.
20 - as much as possible to reduce the temperature of the supercharger, can greatly improve the service life of the sealing ring, reduce cost.
21 appropriate to reduce the pressure, not only does not reduce the cutting efficiency, but also can greatly improve the life of wearing parts.
22 in the processing of brittle materials (such as glass, ceramics, etc.), reduce the pressure of drilling can effectively control the damage of the material.
23 to the numerical control system on the U disk interface with a USB extension cord, so you do not have to worry about duplication of plug U disk caused by poor contact or U disk damage.

上一篇:What are the common fault of NC and how to remove?下一篇:没有了

CONTACT US

Free Call

13827748026

FAX

0757-63858669

EMAIL

fsyuanli@hotmail.com

ADD

No.3 Xingfa Road,Luocun Xiabai The Third Industrial Zone,Nanhai District Foshan Guangdong China

-
QQ

Online Service

  • QQ:QQ
  • 扫一扫